STMicroelectronics /STM32U073 /LPUART1 /LPUART_ISR_ALTERNATE

Parity error This bit is set by hardware when a parity error occurs in Reception mode. It is cleared by software, writing 1 to the PECF in the LPUART_ICR register. An interrupt is generated if PEIE = 1 in the LPUART_CR1 register. Note: In FIFO mode, this error is associated with the character in the LPUART_RDR.

0 (B_0x0): No parity error

1 (B_0x1): Parity error

Framing error This bit is set by hardware when a de-synchronization, excessive noise or a break character is detected. It is cleared by software, writing 1 to the FECF bit in the LPUART_ICR register. When transmitting data in Smartcard mode, this bit is set when the maximum number of transmit attempts is reached without success (the card NACKs the data frame). An interrupt is generated if EIE1=11 in the LPUART_CR3 register. Note: In FIFO mode, this error is associated with the character in the LPUART_RDR.

0 (B_0x0): No Framing error is detected

1 (B_0x1): Framing error or break character is detected

Start bit noise detection flag This bit is set by hardware when noise is detected on the start bit of a received frame. It is cleared by software, writing 1 to the NFCF bit in the LPUART_ICR register. Note: This bit does not generate an interrupt as it appears at the same time as the RXNE/RXFNE bit which itself generates an interrupt. An interrupt is generated when the NE flag is set during multi buffer communication if the EIE bit is set. Note: In FIFO mode, this error is associated with the character in the LPUART_RDR.

0 (B_0x0): No noise is detected

1 (B_0x1): Noise is detected

Overrun error This bit is set by hardware when the data currently being received in the shift register is ready to be transferred into the LPUART_RDR register while RXNE=1 (RXFF = 1 in case FIFO mode is enabled). It is cleared by a software, writing 1 to the ORECF, in the LPUART_ICR register. An interrupt is generated if RXNEIE=1 in the LPUART_CR1 register, or EIE = 1 in the LPUART_CR3 register. Note: When this bit is set, the LPUART_RDR register content is not lost but the shift register is overwritten. An interrupt is generated if the ORE flag is set during multi buffer communication if the EIE bit is set. Note: This bit is permanently forced to 0 (no overrun detection) when the bit OVRDIS is set in the LPUART_CR3 register.

1 (B_0x1): Overrun error is detected

Idle line detected This bit is set by hardware when an Idle Line is detected. An interrupt is generated if IDLEIE=1 in the LPUART_CR1 register. It is cleared by software, writing 1 to the IDLECF in the LPUART_ICR register. Note: The IDLE bit is not set again until the RXNE bit has been set (i.e. a new idle line occurs). Note: If Mute mode is enabled (MME=1), IDLE is set if the LPUART is not mute (RWU=0), whatever the Mute mode selected by the WAKE bit. If RWU=1, IDLE is not set.

0 (B_0x0): No Idle line is detected

1 (B_0x1): Idle line is detected

Read data register not empty RXNE bit is set by hardware when the content of the LPUART_RDR shift register has been transferred to the LPUART_RDR register. It is cleared by a read to the LPUART_RDR register. The RXNE flag can also be cleared by writing 1 to the RXFRQ in the LPUART_RQR register. The RXFNE flag can also be cleared by writing 1 to the RXFRQ in the LPUART_RQR register. An interrupt is generated if RXNEIE=1 in the LPUART_CR1 register.

0 (B_0x0): Data is not received

1 (B_0x1): Received data is ready to be read.

Transmission complete This bit indicates that the last data written in the USART_TDR has been transmitted out of the shift register. The TC flag is set when the transmission of a frame containing data is complete and when TXE is set. An interrupt is generated if TCIE=1 in the LPUART_CR1 register. TC bit is cleared by software by writing 1 to the TCCF in the USART_ICR register or by writing to the USART_TDR register.

Transmit data register empty TXE is set by hardware when the content of the LPUART_TDR register has been transferred into the shift register. It is cleared by a write to the LPUART_TDR register. An interrupt is generated if the TXEIE bit =1 in the LPUART_CR1 register. Note: This bit is used during single buffer transmission.

0 (B_0x0): Data register is full/Transmit FIFO is full.

1 (B_0x1): Data register/Transmit FIFO is not full.

CTS interrupt flag This bit is set by hardware when the CTS input toggles, if the CTSE bit is set. It is cleared by software, by writing 1 to the CTSCF bit in the LPUART_ICR register. An interrupt is generated if CTSIE=1 in the LPUART_CR3 register. Note: If the hardware flow control feature is not supported, this bit is reserved and kept at reset value.

0 (B_0x0): No change occurred on the CTS status line

1 (B_0x1): A change occurred on the CTS status line

CTS flag This bit is set/reset by hardware. It is an inverted copy of the status of the CTS input pin. Note: If the hardware flow control feature is not supported, this bit is reserved and kept at reset value.

0 (B_0x0): CTS line set

1 (B_0x1): CTS line reset

Busy flag This bit is set and reset by hardware. It is active when a communication is ongoing on the RX line (successful start bit detected). It is reset at the end of the reception (successful or not).

0 (B_0x0): LPUART is idle (no reception)

1 (B_0x1): Reception on going

Character match flag This bit is set by hardware, when a the character defined by ADD[7:0] is received. It is cleared by software, writing 1 to the CMCF in the LPUART_ICR register. An interrupt is generated if CMIE=1in the LPUART_CR1 register.

0 (B_0x0): No Character match detected

1 (B_0x1): Character match detected

Send break flag This bit indicates that a send break character was requested. It is set by software, by writing 1 to the SBKRQ bit in the LPUART_CR3 register. It is automatically reset by hardware during the stop bit of break transmission.

0 (B_0x0): No break character transmitted

1 (B_0x1): Break character transmitted

Receiver wake-up from Mute mode This bit indicates if the LPUART is in Mute mode. It is cleared/set by hardware when a wake-up/mute sequence is recognized. The Mute mode control sequence (address or IDLE) is selected by the WAKE bit in the LPUART_CR1 register. When wake-up on IDLE mode is selected, this bit can only be set by software, writing 1 to the MMRQ bit in the LPUART_RQR register. Note: If the LPUART does not support the wake-up from Stop feature, this bit is reserved and kept at reset value.

0 (B_0x0): Receiver in Active mode

1 (B_0x1): Receiver in Mute mode

Wake-up from low-power mode flag This bit is set by hardware, when a wake-up event is detected. The event is defined by the WUS bitfield. It is cleared by software, writing a 1 to the WUCF in the LPUART_ICR register. An interrupt is generated if WUFIE=1 in the LPUART_CR3 register. Note: When UESM is cleared, WUF flag is also cleared. Note: If the USART does not support the wake-up from Stop feature, this bit is reserved and kept at reset value. Refer to Section132.3: LPUART implementation on page1914.

Transmit enable acknowledge flag This bit is set/reset by hardware, when the Transmit Enable value is taken into account by the LPUART. It can be used when an idle frame request is generated by writing TE=0, followed by TE=1 in the LPUART_CR1 register, in order to respect the TE=0 minimum period.

Receive enable acknowledge flag This bit is set/reset by hardware, when the Receive Enable value is taken into account by the LPUART. It can be used to verify that the LPUART is ready for reception before entering low-power mode. Note: If the LPUART does not support the wake-up from Stop feature, this bit is reserved and kept at reset value.