LPWRRSTF=B_0x0, SFTRSTF=B_0x0, LSIPREDIV=B_0x0, IWDGRSTF=B_0x0, LSION=B_0x0, PWRRSTF=B_0x0, PINRSTF=B_0x0, OBLRSTF=B_0x0, LSIRDY=B_0x0, WWDGRSTF=B_0x0, RMVF=B_0x0
Control/status register
| LSION | LSI oscillator enable Set and cleared by software to enable/disable the LSI oscillator: 0 (B_0x0): Disable 1 (B_0x1): Enable |
| LSIRDY | LSI oscillator ready Set and cleared by hardware to indicate when the LSI oscillator is ready (stable): After the LSION bit is cleared, LSIRDY goes low after 3 LSI oscillator clock cycles. This bit can be set even if LSION = 0 if the LSI is requested by the Clock Security System on LSE, by the Independent Watchdog or by the RTC. 0 (B_0x0): Not ready 1 (B_0x1): Ready |
| LSIPREDIV | Internal low-speed oscillator pre-divided by 128 Set and reset by hardware to indicate when the low-speed internal RC oscillator has to be divided by 128. The software has to switch off the LSI before changing this bit. 0 (B_0x0): LSI RC oscillator is not divided 1 (B_0x1): LSI RC oscillator is divided by 128 |
| MSISRANGE | MSI range after Standby mode Set by software to chose the MSI frequency at startup. This range is used after exiting Standby mode until MSIRGSEL is set. After a pad or a power-on reset, the range is always 41MHz. MSISRANGE[3:0] can be written only when MSIRGSEL1=11. Others: Reserved Note: Changing the MSISRANGE[3:0] does not change the current MSI frequency. 4 (B_0x4): Range 7 around 81MHz |
| RMVF | Remove reset flags Set by software to clear the reset flags. 0 (B_0x0): No effect 1 (B_0x1): Clear reset flags |
| OBLRSTF | Option byte loader reset flag Set by hardware when a reset from the Option byte loading occurs. Cleared by setting the RMVF bit. 0 (B_0x0): No reset from Option byte loading occurred 1 (B_0x1): Reset from Option byte loading occurred |
| PINRSTF | Pin reset flag Set by hardware when a reset from the NRST pin occurs. Cleared by setting the RMVF bit. 0 (B_0x0): No reset from NRST pin occurred 1 (B_0x1): Reset from NRST pin occurred |
| PWRRSTF | BOR or POR/PDR flag Set by hardware when a BOR or POR/PDR occurs. Cleared by setting the RMVF bit. 0 (B_0x0): No BOR or POR occurred 1 (B_0x1): BOR or POR occurred |
| SFTRSTF | Software reset flag Set by hardware when a software reset occurs. Cleared by setting the RMVF bit. 0 (B_0x0): No software reset occurred 1 (B_0x1): Software reset occurred |
| IWDGRSTF | Independent window watchdog reset flag Set by hardware when an independent watchdog reset domain occurs. Cleared by setting the RMVF bit. 0 (B_0x0): No independent watchdog reset occurred 1 (B_0x1): Independent watchdog reset occurred |
| WWDGRSTF | Window watchdog reset flag Set by hardware when a window watchdog reset occurs. Cleared by setting the RMVF bit. 0 (B_0x0): No window watchdog reset occurred 1 (B_0x1): Window watchdog reset occurred |
| LPWRRSTF | Low-power reset flag Set by hardware when a reset occurs due to illegal Stop, Standby, or Shutdown mode entry. Cleared by setting the RMVF bit. This operates only if nRST_STOP, nRST_STDBY or nRST_SHDW option bits are cleared. 0 (B_0x0): No illegal mode reset occurred 1 (B_0x1): Illegal mode reset occurred |