MSIZE=B_0x0, TCIE=B_0x0, DIR=B_0x0, CIRC=B_0x0, PINC=B_0x0, PL=B_0x0, TEIE=B_0x0, EN=B_0x0, MEM2MEM=B_0x0, MINC=B_0x0, HTIE=B_0x0, PSIZE=B_0x0
DMA channel 1 configuration register
| EN | Channel enable When a channel transfer error occurs, this bit is cleared by hardware. It can not be set again by software (channel x re-activated) until the TEIFx bit of the DMA_ISR register is cleared (by1setting the CTEIFx bit of the DMA_IFCR register). Note: This bit is set and cleared by software. 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| TCIE | Transfer complete interrupt enable Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| HTIE | Half transfer interrupt enable Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| TEIE | Transfer error interrupt enable Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| DIR | Data transfer direction This bit must be set only in memory-to-peripheral and peripheral-to-memory modes. Source attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Destination attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Destination attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Source attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): Read from peripheral 1 (B_0x1): Read from memory |
| CIRC | Circular mode Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| PINC | Peripheral increment mode Defines the increment mode for each DMA transfer to the identified peripheral. n memory-to-memory mode, this bit identifies the memory destination if DIR = 1 and the memory source if DIR = 0. In peripheral-to-peripheral mode, this bit identifies the peripheral destination if DIR = 1 and the peripheral source if DIR = 0. Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| MINC | Memory increment mode Defines the increment mode for each DMA transfer to the identified memory. In memory-to-memory mode, this bit identifies the memory source if DIR = 1 and the memory destination if DIR = 0. In peripheral-to-peripheral mode, this bit identifies the peripheral source if DIR = 1 and the peripheral destination if DIR = 0. Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |
| PSIZE | Peripheral size Defines the data size of each DMA transfer to the identified peripheral. In memory-to-memory mode, this bitfield identifies the memory destination if DIR = 1 and the memory source if DIR = 0. In peripheral-to-peripheral mode, this bitfield identifies the peripheral destination if DIR = 1 and the peripheral source if DIR = 0. Note: This bitfield is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): 8 bits 1 (B_0x1): 16 bits 2 (B_0x2): 32 bits |
| MSIZE | Memory size Defines the data size of each DMA transfer to the identified memory. In memory-to-memory mode, this bitfield identifies the memory source if DIR = 1 and the memory destination if DIR = 0. In peripheral-to-peripheral mode, this bitfield identifies the peripheral source if DIR = 1 and the peripheral destination if DIR = 0. Note: This bitfield is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): 8 bits 1 (B_0x1): 16 bits 2 (B_0x2): 32 bits |
| PL | Priority level Note: This bitfield is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): Low 1 (B_0x1): Medium 2 (B_0x2): High 3 (B_0x3): Very high |
| MEM2MEM | Memory-to-memory mode Note: This bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN = 1). 0 (B_0x0): Disabled 1 (B_0x1): Enabled |