STMicroelectronics /STM32U545 /GPDMA1 /GPDMA_C9TR2

DMA hardware request selection If the channel x is activated (i.e. GPDMA_CxCR.EN is asserted) with SWREQ=1 (i.e. software request for a memory-to-memory transfer), this bit is ignored. Else, the selected hardware request as per Table 12 is internally taken into account. Note: The user must not assign a same input hardware request (i.e. a same REQSEL[6:0] value) to different active DMA channels (i.e. if GPDMA_CxCR.EN=1 and GPDMA_CxTR2.SWREQ=0 for the related x channels). In other words, DMA is not intended to hardware support the case of simultaneous enabled channels having been -incorrectly- configured with a same hardware peripheral request signal, and there is no user setting error reporting.

Software request When GPDMA_CxCR.EN is asserted, this field is internally taken into account: - 0: no software request. The selected hardware request REQSEL[6:0] is taken into account. - 1: software request (for a memory-to-memory transfer). And the default selected hardware request as per REQSEL[6:0] is ignored.

Destination hardware request If the channel x is activated (i.e. GPDMA_CxCR.EN is asserted) with SWREQ=1 (i.e. software request for a memory-to-memory transfer), this bit is ignored. Else: - 0: the selected hardware request is driven by a source peripheral (i.e. this request signal is taken into account by the DMA transfer scheduler over the source/read port) - 1: the selected hardware request is driven by a destination peripheral (.e. this request signal is taken into account by the DMA transfer scheduler over the destination/write port)

BREQ

Trigger mode: Defines the transfer granularity for its conditioning by the trigger. If the channel x is enabled (i.e. when GPDMA_CxCR.EN is asserted) with TRIGPOL[1:0]=00 or 11, these bits are ignored. Else, a DMA transfer is conditioned by (at least) one trigger hit, either at: - 00: at block level (for channel x=12 to 15: for each block if a 2D/repeated block is configured i.e. if GPDMA_CxBR1.BRC[10:0]! = 0): the first burst read of a/each block transfer is conditioned by one hit trigger. - 01: at 2D/repeated block level for channel x=12 to 15; same as 00 for channel x=0 to 11: the first burst read of a 2D/repeated block transfer is conditioned by one hit trigger.

Trigger event input selection Note: Selects the trigger event input as per Table 13 of the DMA transfer, with an active trigger event if TRIGPOL[1:0] !=00.

Trigger event polarity Defines the polarity of the selected trigger event input defined by TRIGSEL[5:0]. - 00: no trigger. Masked trigger event. - 01: trigger on the rising edge - 10: trigger on the falling edge - 11: same as 00

Transfer complete event mode Defines the transfer granularity for the transfer complete (and half transfer complete) event generation. - 00: at block level (i.e. when GPDMA_CxBR1.BNDT[15:0]= 0): the complete (and the half) transfer event is generated at the (respectively half of the) end of a block. Note: If the initial LLI0 data transfer is null/void (i.e. directly programmed by the internal register file with GPDMA_CxBR1.BNDT[15:0]=0), then neither the complete transfer event nor the half transfer event is generated. - 01: channel x=0 to 11: same as 00 ;channel x=12 to 15: at 2D/repeated block level (i.e. when GPDMA_CxBR1.BRC[10:0]= 0 and GPDMA_CxBR1.BNDT[15:0]= 0): the complete (and the half) transfer event is generated at the end (respectively half of the end) of the 2D/repeated block Note: If the initial LLI0 data transfer is null/void (i.e. directly programmed by the internal register file with GPDMA_CxBR1.BNDT[15:0]=0), then neither the complete transfer event nor the half transfer event is generated. - 10: at LLI level: the complete transfer event is generated at the end of the LLI transfer, including the update of the LLI if any. The half transfer event is generated at the half of the LLI data transfer (the LLI data transfer being a block or a 2D/repeated block transfer), if any data transfer. Note: If the initial LLI0 data transfer is null/void (i.e. directly programmed by the internal register file with GPDMA_CxBR1.BNDT[15:0]=0), then the half transfer event is not generated, and the transfer complete event is generated when is completed the loading of the LLI1. - 11: at channel level: the complete transfer event is generated at the end of the last LLI transfer. The half transfer event is generated at the half of the data transfer of the last LLI. The last LLI is the one that updates the link address GPDMA_CxLLR.LA[15:2] to zero and that clears all the update bits - UT1, UT2, UB1, USA, UDA, if present UT3, UB2 and ULL - of the GPDMA_CxLLR register. If the channel transfer is continuous/infinite, no event is generated.