OT9=B_0x0, OT14=B_0x0, OT7=B_0x0, OT12=B_0x0, OT6=B_0x0, OT3=B_0x0, OT15=B_0x0, OT2=B_0x0, OT10=B_0x0, OT8=B_0x0, OT4=B_0x0, OT13=B_0x0, OT5=B_0x0, OT0=B_0x0, OT11=B_0x0, OT1=B_0x0
GPIO port output type register
| OT0 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT1 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT2 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT3 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT4 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT5 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT6 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT7 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT8 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT9 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT10 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT11 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT12 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT13 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT14 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |
| OT15 | Port x configuration I/O pin y These bits are written by software to configure the I/O output type. Note: This bit is reserved and must be kept at reset value when the corresponding I/O is not available on the selected package. 0 (B_0x0): Output push-pull (reset state) 1 (B_0x1): Output open-drain |