STMicroelectronics /STM32U5Gx /LPDMA1 /LPDMA_C1CR

enable - 0: write: ignored, read: channel disabled - 1: write: enable channel, read: channel enabled Writing 1 into the field RESET (bit 1) causes the hardware to de-assert this bit, whatever is written into this bit 0. Else: * this bit is de-asserted by hardware when there is a transfer error (master bus error or user setting error) or when there is a channel transfer complete (channel ready to be configured, e.g. if LSM=1 at the end of a single execution of the LLI). * Else, this bit can be asserted by software. Writing 0 into this EN bit is ignored.

reset - 0: no channel reset - 1: channel reset This bit is write only. Writing 0 has no impact. Writing 1 implies/will imply the reset of the FIFO, the reset of the channel internal state, and the reset of the SUSP and EN bits, whatever is written in respectively bit 2 and bit 0. The reset is/will be effective when the channel is in state i.e. either i) the active channel is in suspended state (i.e. LPDMA_CxSR.SUSPF=1 and LPDMA_CxSR.IDLEF=1 and LPDMA_CxCR.EN=1) or ii) the channel is in disabled state (i.e. LPDMA_CxSR.IDLEF=1 and LPDMA_CxCR.EN=0). After writing a RESET, if the user wants to continue using this channel, the user should explicitly reconfigure the channel including the hardware-modified configuration registers LPDMA_CxBR1, LPDMA_CxSAR and LPDMA_CxDAR, before enabling again the channel. Following the programming sequence in Figure 4: DMA channel abort and restart sequence.

suspend - 0: write: resume channel, read: channel not suspended - 1: write: suspend channel, read: channel suspended Writing 1 into the field RESET (bit 1) causes the hardware to de-assert this bit, whatever is written into this bit 2. Else: Software must write 1 in order to suspend an active channel i.e. a channel with an on-going DMA transfer over its master ports. Software must write 0 in order to resume a suspended channel, following the programming sequence in Figure 3: DMA channel suspend and resume sequence.

transfer complete interrupt enable - 0: interrupt disabled - 1: interrupt enabled

half transfer complete interrupt enable - 0: interrupt disabled - 1: interrupt enabled

data transfer error interrupt enable - 0: interrupt disabled - 1: interrupt enabled

update link transfer error interrupt enable - 0: interrupt disabled - 1: interrupt enabled

user setting error interrupt enable - 0: interrupt disabled - 1: interrupt enabled

completed suspension interrupt enable - 0: interrupt disabled - 1: interrupt enabled

Link Step mode:- 0: channel is executed for the full linked-list, and completed at the end (if any) of the last LLI i.e. when LPDMA_CxLLR=0: the 16 low significant bits of the link address are null (LA[15:0]=0) and all the update bits are null i.e. UT1=UB1=UT2=USA=UDA=UB2 =UT3=ULL=0. Then LPDMA_CxBR1.BRC[10:0]=0 and LPDMA_CxBR1.BNDT[15:0]=0.- 1: channel is executed once for the current LLI:* First the (possibly 2D/repeated) block transfer is executed as defined by the current internal register file until that (LPDMA_CxBR1.BRC[10:0]=0 and LPDMA_CxBR1.BNDT[15:0]=0).* Secondly the next linked-list data structure is conditionally uploaded from memory as defined by LPDMA_CxLLR register. Then channel execution is completed.Note: This bit must be written when EN=0. This bit is read-only when EN=1.

priority level of the DMA transfer of the channel x vs others- 00: low priority, low weight- 01: low priority, mid weight- 10: low priority, high weight- 11: high priorityNote: This bit must be written when EN=0. This bit is read-only when EN=1.