WUPPUPD6=B_0x0, WUPPUPD2=B_0x0, WUPPUPD7=B_0x0, WUPP7=B_0x0, WUPP4=B_0x0, WUPEN4=B_0x0, WUPPUPD1=B_0x0, WUPEN2=B_0x0, WUPEN1=B_0x0, WUPEN3=B_0x0, WUPP2=B_0x0, WUPPUPD4=B_0x0, WUPEN5=B_0x0, WUPP6=B_0x0, WUPP1=B_0x0, WUPPUPD8=B_0x0, WUPP8=B_0x0, WUPP3=B_0x0, WUPEN7=B_0x0, WUPPUPD3=B_0x0, WUPP5=B_0x0, WUPEN8=B_0x0, WUPEN6=B_0x0, WUPPUPD5=B_0x0
PWR wakeup configuration register
| WUPEN1 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN2 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN3 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN4 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN5 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN6 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN7 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPEN8 | enable wakeup pin WUPx These bits are set and cleared by software. Note: an additional wakeup event is detected if WUPx pin is enabled (by setting the WUPENx bit) when WUPx pin level is already high when WUPPx selects rising edge, or low when WUPPx selects falling edge. 0 (B_0x0): an event on WUPx pin does not wakeup the system from Standby mode. 1 (B_0x1): a rising or falling edge on WUPx pin wakes up the system from Standby mode. |
| WUPP1 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP2 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP3 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP4 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP5 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP6 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP7 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPP8 | wakeup pin polarity bit for WUPx These bits define the polarity used for event detection on WUPx external wakeup pin. 0 (B_0x0): detection on high level (rising edge) 1 (B_0x1): detection on low level (falling edge) |
| WUPPUPD1 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD2 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD3 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD4 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD5 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD6 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD7 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |
| WUPPUPD8 | wakeup pin pull configuration for WKUPx These bits define the I/O pad pull configuration used when WUPENx = 1. The associated GPIO port pull configuration must be set to the same value or to 00. The wakeup pin pull configuration is kept in Standby mode. 0 (B_0x0): no pull-up 1 (B_0x1): pull-up 2 (B_0x2): pull-down |