BOOTACKEN=B_0x0, DTDIR=B_0x0, DTEN=B_0x0, DBLOCKSIZE=B_0x0, RWMOD=B_0x0, DTMODE=B_0x0, FIFORST=B_0x0, RWSTOP=B_0x0
SDMMC data control register
| DTEN | Data transfer enable bit 0 (B_0x0): Do not start data transfer without CPSM data transfer command. 1 (B_0x1): Start data transfer without CPSM data transfer command. |
| DTDIR | Data transfer direction selection 0 (B_0x0): From host to card. 1 (B_0x1): From card to host. |
| DTMODE | Data transfer mode selection 0 (B_0x0): Block data transfer ending on block count. 1 (B_0x1): SDIO multibyte data transfer. 2 (B_0x2): e MMC Stream data transfer. 3 (B_0x3): Block data transfer ending with STOP_TRANSMISSION command (not to be used with DTEN initiated data transfers). |
| DBLOCKSIZE | Data block size 0 (B_0x0): Block length = 2less thansup>0less than/sup> = 1 byte 1 (B_0x1): Block length = 2less thansup>1less than/sup> = 2 bytes 2 (B_0x2): Block length = 2less thansup>2 less than/sup>= 4 bytes 3 (B_0x3): Block length = 2less thansup>3less than/sup> = 8 bytes 4 (B_0x4): Block length = 2less thansup>4less than/sup> = 16 bytes 5 (B_0x5): Block length = 2less thansup>5less than/sup> = 32 bytes 6 (B_0x6): Block length = 2less thansup>6less than/sup> = 64 bytes 7 (B_0x7): Block length = 2less thansup>7less than/sup> = 128 bytes 8 (B_0x8): Block length = 2less thansup>8less than/sup> = 256 bytes 9 (B_0x9): Block length = 2less thansup>9less than/sup> = 512 bytes 10 (B_0xA): Block length = 2less thansup>10less than/sup> = 1024 bytes 11 (B_0xB): Block length = 2less thansup>11less than/sup> = 2048 bytes 12 (B_0xC): Block length = 2less thansup>12less than/sup> = 4096 bytes 13 (B_0xD): Block length = 2less thansup>13less than/sup> = 8192 bytes 14 (B_0xE): Block length = 2less thansup>14less than/sup> = 16384 bytes |
| RWSTART | Read Wait start |
| RWSTOP | Read Wait stop 0 (B_0x0): No Read Wait stop. 1 (B_0x1): Enable for Read Wait stop when DPSM is in the R_W state. |
| RWMOD | Read Wait mode 0 (B_0x0): Read Wait control using SDMMC_D2 1 (B_0x1): Read Wait control stopping SDMMC_CK |
| SDIOEN | SD I/O interrupt enable functions |
| BOOTACKEN | Enable the reception of the boot acknowledgment 0 (B_0x0): Boot acknowledgment disabled, not expected to be received 1 (B_0x1): Boot acknowledgment enabled, expected to be received |
| FIFORST | FIFO reset, flushes any remaining data 0 (B_0x0): FIFO not affected. 1 (B_0x1): Flush any remaining data and reset the FIFO pointers. |