stm32 /stm32wb0 /STM32WB05 /LPUART /CR3

EIE: Error interrupt enable Error Interrupt Enable Bit is required to enable interrupt generation in case of a framing error, overrun error noise flag or SPI slave underrun error (FE=1 or ORE=1 or NF=1or UDR = 1 in the USART_ISR register). -0: Interrupt is inhibited -1: An interrupt is generated when FE=1 or ORE=1 or NF=1 or UDR = 1 (in SPI slave mode) in the USART_ISR register.

HDSEL: Half-duplex selection Selection of Single-wire Half-duplex mode -0: Half duplex mode is not selected -1: Half duplex mode is selected This bit can only be written when the USART is disabled (UE=0).

DMAR: DMA enable receiver This bit is set/reset by software -1: DMA mode is enabled for reception -0: DMA mode is disabled for reception

DMAT: DMA enable transmitter This bit is set/reset by software -1: DMA mode is enabled for transmission -0: DMA mode is disabled for transmission

RTSE: RTS enable -0: RTS hardware flow control disabled -1: RTS output enabled, data is only requested when there is space in the receive buffer. The transmission of data is expected to cease after the current character has been transmitted. The nRTS output is asserted (pulled to 0) when data can be received. This bit can only be written when the USART is disabled (UE=0).

CTSE: CTS enable -0: CTS hardware flow control disabled -1: CTS mode enabled, data is only transmitted when the nCTS input is asserted (tied to 0). If the nCTS input is deasserted while data is being transmitted, then the transmission is completed before stopping. If data is written into the data register while nCTS is asserted, the transmission is postponed until nCTS is asserted. This bit can only be written when the USART is disabled (UE=0)

CTSIE: CTS interrupt enable -0: Interrupt is inhibited -1: An interrupt is generated whenever CTSIF=1 in the USART_ISR register

OVRDIS: Overrun Disable This bit is used to disable the receive overrun detection. -0: Overrun Error Flag, ORE, is set when received data is not read before receiving new data. -1: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the USART_RDR register. When FIFO mode is enabled, the RXFIFO will be bypassed and data will be written directly in USARTx_RDR register. Even when FIFO management is enabled, the RXNE flag is to be used. This bit can only be written when the USART is disabled (UE=0).

DDRE: DMA Disable on Reception Error -0: DMA is not disabled in case of reception error. The corresponding error flag is set but RXNE is kept 0 preventing from overrun. As a consequence, the DMA request is not asserted, so the erroneous data is not transferred (no DMA request), but next correct received data will be transferred. (used for Smartcard mode) -1: DMA is disabled following a reception error. The corresponding error flag is set, as well as RXNE. The DMA request is masked until the error flag is cleared. This means that the software must first disable the DMA request (DMAR = 0) or clear RXNE(RXFNE is case FIFO mode is enabled) before clearing the error flag. This bit can only be written when the USART is disabled (UE=0).

DEM: Driver enable mode This bit allows the user to activate the external transceiver control, through the DE signal. -0: DE function is disabled. -1: DE function is enabled. The DE signal is output on the RTS pin. This bit can only be written when the USART is disabled (UE=0).

DEP: Driver enable polarity selection -0: DE signal is active high. -1: DE signal is active low. This bit can only be written when the USART is disabled (UE=0).

WUS[1:0]: Wakeup from Stop mode interrupt flag selection This bit-field specify the event which activates the WUF (Wakeup from Stop mode flag). -00: WUF active on address match (as defined by ADD[7:0] and ADDM7) -01:Reserved. -10: WUF active on Start bit detection -11: WUF active on RXNE. This bit field can only be written when the LPUART is disabled (UE=0).

WUFIE: Wakeup from Stop mode interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An LPUART interrupt is generated whenever WUF=1 in the LPUART_ISR register

TXFTIE: TXFIFO threshold interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An USART interrupt is generated when TXFIFO reaches the threshold programmed in TXFTCFG.

RXFTCFG: Receive FIFO threshold configuration -000:Receive FIFO reaches 1/8 of its depth. -001:Receive FIFO reaches 1/4 of its depth. -010:Receive FIFO reaches 1/2 of its depth. -011:Receive FIFO reaches 3/4 of its depth. -100:Receive FIFO reaches 7/8 of its depth. -101:Receive FIFO becomes full. Remaining combinations: Reserved.

RXFTIE: RXFIFO threshold interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An USART interrupt is generated when Receive FIFO reaches the threshold programmed in RXFTCFG.

TXFTCFG: TXFIFO threshold configuration -000:TXFIFO reaches 1/8 of its depth. -001:TXFIFO reaches 1/4 of its depth. -010:TXFIFO reaches 1/2 of its depth. -011:TXFIFO reaches 3/4 of its depth. -100:TXFIFO reaches 7/8 of its depth. -101:TXFIFO becomes empty. Remaining combinations: Reserved.