stm32 /stm32wb0 /STM32WB05 /TIM2 /SMCR

SMS: Slave mode selection

When external signals are selected the active edge of the trigger signal (TRGI) is linked to

the polarity selected on the external input (see Input Control register and Control Register

description.

0000: Slave mode disabled - if CEN = ‘1’ then the prescaler is clocked directly by the internal

clock.

0001: Encoder mode 1 - Counter counts up/down on TI2FP2 edge depending on TI1FP1

level.

0010: Encoder mode 2 - Counter counts up/down on TI1FP1 edge depending on TI2FP2

level.

0011: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges

depending on the level of the other input.

0100: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter

and generates an update of the registers.

0101: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The

counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of

the counter are controlled.

0110: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not

reset). Only the start of the counter is controlled.

0111: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

1000: Combined reset + trigger mode - Rising edge of the selected trigger input (TRGI)

reinitializes the counter, generates an update of the registers and starts the counter.

Codes above 1000: Reserved.

Note: The gated mode must not be used if TI1F_ED is selected as the trigger input

(TS=‘100’). Indeed, TI1F_ED outputs 1 pulse for each transition on TI1F, whereas the

gated mode checks the level of the trigger signal.

OCCS: OCREF clear selection

This bit is used to select the OCREF clear source.

0: OCREF_CLR_INT is connected to the OCREF_CLR input (stuck at 0 so no effect)

1: OCREF_CLR_INT is connected to ETRF

TS[2:0]: Trigger selection

This bit-field selects the trigger input to be used to synchronize the counter.

101: Filtered Timer Input 1 (TI1FP1)

110: Filtered Timer Input 2 (TI2FP2)

others: Reserved

Note: These bits must be changed only when they are not used (e.g. when SMS=000) to

avoid wrong edge detections at the transition.

MSM: Master/Slave mode

Not vailable in IUM. Not used in Blue51 as TRGO is not connected to any slave timer

0: No action

1: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect

synchronization between the current timer and its slaves (through TRGO). It is useful if we

want to synchronize several timers on a single external event.

ETF[3:0]: External trigger filter

This bit-field then defines the frequency used to sample ETRP signal and the length of the

digital filter applied to ETRP. The digital filter is made of an event counter in which N events

are needed to validate a transition on the output:

0000: No filter, sampling is done at fDTS

0001: fSAMPLING=fCK_INT, N=2

0010: fSAMPLING=fCK_INT, N=4

0011: fSAMPLING=fCK_INT, N=8

0100: fSAMPLING=fDTS/2, N=6

0101: fSAMPLING=fDTS/2, N=8

0110: fSAMPLING=fDTS/4, N=6

0111: fSAMPLING=fDTS/4, N=8

1000: fSAMPLING=fDTS/8, N=6

1001: fSAMPLING=fDTS/8, N=8

1010: fSAMPLING=fDTS/16, N=5

1011: fSAMPLING=fDTS/16, N=6

1100: fSAMPLING=fDTS/16, N=8

1101: fSAMPLING=fDTS/32, N=5

1110: fSAMPLING=fDTS/32, N=6

1111: fSAMPLING=fDTS/32, N=8

ETPS[1:0]: External trigger prescaler

External trigger signal ETRP frequency must be at most 1/4 of TIMxCLK frequency. A

prescaler can be enabled to reduce ETRP frequency. It is useful when inputting fast external

clocks.

00: Prescaler OFF

01: ETRP frequency divided by 2

10: ETRP frequency divided by 4

11: ETRP frequency divided by 8

ECE: External clock enable

This bit enables External clock mode 2.

0: External clock mode 2 disabled

1: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF

signal.

Note: 1: Setting the ECE bit has the same effect as selecting external clock mode 1 with

TRGI connected to ETRF (SMS=111 and TS=111).

Note: 2: It is possible to simultaneously use external clock mode 2 with the following slave

modes: reset mode, gated mode and trigger mode. Nevertheless, TRGI must not be

connected to ETRF in this case (TS bits must not be 111).

Note: 3: If external clock mode 1 and external clock mode 2 are enabled at the same time,

the external clock input is ETRF.

ETP: External trigger polarity

This bit selects whether ETR or ETR is used for trigger operations

0: ETR is non-inverted, active at high level or rising edge.

1: ETR is inverted, active at low level or falling edge.

SMS[3]: Slave mode selection - bit 3

Refer to SMS description - bits2:0

Extended trigger selection. Not used. Not available in IUM