EOBIE=B_0x0
CR1 register
| UE | UE: USART enable When this bit is cleared, the USART prescalers and outputs are stopped immediately, and current operations are discarded. The configuration of the USART is kept, but all the status flags, in the USART_ISR are reset. This bit is set and cleared by software. -0: USART prescaler and outputs disabled, low power mode -1: USART enabled |
| RE | RE: Receiver enable This bit enables the receiver. It is set and cleared by software. -0: Receiver is disabled -1: Receiver is enabled and begins searching for a start bit |
| TE | TE: Transmitter enable This bit enables the transmitter. It is set and cleared by software. -0: Transmitter is disabled -1: Transmitter is enabled |
| IDLEIE | IDLEIE: IDLE interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: A USART interrupt is generated whenever IDLE=1 in the USART_ISR register |
| RXNEIE_RXFNEIE | RXNEIE/RXFNEIE: Receive data register not empty/RXFIFO not empty interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An USART interrupt is generated whenever ORE=1 or RXNE/RXFNE=1 in the USART_ISR register |
| TCIE | TCIE: Transmission complete interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: A USART interrupt is generated whenever TC=1 in the USART_ISR register |
| TXEIE_TXFNFIE | TXEIE/TXFNFIE: Transmit data regsiter empty/TXFIFO not full interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: A USART interrupt is generated whenever TXE/TXFNF =1 in the USART_ISR register |
| PEIE | PEIE: PE interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: A USART interrupt is generated whenever PE=1 in the USART_ISR register |
| PS | PS: Parity selection This bit selects the odd or even parity when the parity generation/detection is enabled (PCE bit set). It is set and cleared by software. The parity will be selected after the current byte. -0: Even parity -1: Odd parity This bit field can only be written when the USART is disabled (UE=0). |
| PCE | PCE: Parity control enable This bit selects the hardware parity control (generation and detection). When the parity control is enabled, the computed parity is inserted at the MSB position (9th bit if M=1; 8th bit if M=0) and parity is checked on the received data. This bit is set and cleared by software. Once it is set, PCE is active after the current byte (in reception and in transmission). -0: Parity control disabled -1: Parity control enabled This bit field can only be written when the USART is disabled (UE=0). |
| WAKE | WAKE: Receiver wakeup method This bit determines the USART wakeup method from Mute mode. It is set or cleared by software. -0: Idle line -1: Address mark This bit field can only be written when the USART is disabled (UE=0). |
| M_0 | M0: Word length This bit, with bit 28 (M1) determine the word length. It is set or cleared by software. See Bit -28 (M1)description. This bit can only be written when the USART is disabled (UE=0). |
| MME | MME: Mute mode enable This bit activates the mute mode function of the USART. When set, the USART can switch between the active and mute modes, as defined by the WAKE bit. It is set and cleared by software. -0: Receiver in active mode permanently -1: Receiver can switch between mute mode and active mode |
| CMIE | CMIE: Character match interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: A USART interrupt is generated when the CMF bit is set in the USART_ISR register. |
| OVER8 | OVER8: Oversampling mode -0: Oversampling by 16 This bit can only be written when the USART is disabled (UE=0). |
| DEDT | DEDT[4:0]: Driver Enable deassertion time This 5-bit value defines the time between the end of the last stop bit, in a transmitted message, and the de-activation of the DE (Driver Enable) signal. It is expressed in sample time units (1/8 or 1/16 bit time, depending on the oversampling rate). If the USART_TDR register is written during the DEDT time, the new data is transmitted only when the DEDT and DEAT times have both elapsed. This bit field can only be written when the USART is disabled (UE=0). |
| DEAT | DEAT[4:0]: Driver Enable assertion time This 5-bit value defines the time between the activation of the DE (Driver Enable) signal and the beginning of the start bit. It is expressed in sample time units (1/8 or 1/16 bit time, depending on the oversampling rate). This bit field can only be written when the USART is disabled (UE=0). |
| RTOIE | RTOIE: Receiver timeout interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An USART interrupt is generated when the RTOF bit is set in the USART_ISR register |
| EOBIE | EOBIE: End of Block interrupt enable This bit is set and cleared by software. 0 (B_0x0): Interrupt is inhibited 1 (B_0x1): A USART interrupt is generated when the EOBF flag is set in the USART_ISR register |
| M_1 | Word length This bit, with bit 12 (M0) determine the word length. It is set or cleared by software. M[1:0] = 00: 1 Start bit, 8 Data bits, n Stop bit M[1:0] = 01: 1 Start bit, 9 Data bits, n Stop bit M[1:0] = 10: 1 Start bit, 7 Data bits, n Stop bit This bit can only be written when the USART is disabled (UE=0).s |
| FIFOEN | FIFOEN :FIFO mode enable This bit is set and cleared by software. -0: FIFO mode is disabled. -1: FIFO mode is enabled. |
| TXFEIE | TXFEIE :TXFIFO empty interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An USART interrupt is generated when TXFE=1 in the USART_ISR register |
| RXFFIE | RXFFIE :RXFIFO Full interrupt enable This bit is set and cleared by software. -0: Interrupt is inhibited -1: An USART interrupt is generated when RXFF=1 in the USART_ISR register |